[JIM] Channel Settings AJA v.6.2

Open

Settings

You can find a description of each Channel setting below:

Device: Select the Video Device (AJA) for this Channel.

Input Mode: Select the Input Mode for this Channel. Available options, depending on the Device are:

• SDI (AJA)

• SDI (AJA 12G)

• HDMI (AJA)

Input: Choose the Input of the Device for this Channel here (for Blackmagic Design Channels, only option “Input #1” is available).

Audio Input: Choose between different Audio Input options. Audio Input options are:

• Auto (same as video, normally SDI)

• SDI (by choosing this option, the audio input channel option can be adjusted as well)

• Analog

• AES/EBU

• External (NEW in v.6.2): When utilizing the External option, a channel can utilize any audio input available within the macOS Sound input preferences as the audio source. Therefore, USB audio interfaces such as the Focusrite Scarlett 2i2 are now supported. Furthermore, the Dante Virtual Soundcard can be utilized as an Audio Input option. Additionally a delay in frames for the video pipeline can be added here. Please note that the delay option is only available when using the External Audio Input option.

Open

Video Mode: Select the Video mode and ensure that it matches the incoming Video Signal, which is attached to the selected Channel. If it does not match, a warning will be shown (“No Signal”).

AJA Frame Buffer: This setting overwrites the default Frame Buffer value of an AJA Channel. This setting is required for UHD recording workflows, where the Channel Frame Buffer can be set to a higher value, to avoid any Dropped Frames while recording.

Enable RP-188 (SDI Embedded) Timecode (AJA only): This option enables the “SDI Embedded” Timecode Source option for an AJA Input Channel. By default, this option is enabled.

Enable End-To-End SDI If Available: This option does work for some specific AJA devices, such as the KONA 1 or the KONA LHe Plus, where the incoming signal will be passed to the output port, once the Just In Engine application is running.

File Overwrite Strategy:

• Append Counter (Default): When using this option, the Just In Engine application will add “_2” to the actual file name to avoid overwriting an already existing file.

• Replace: By choosing this option, the Just In Engine application will overwrite a file with the same name at the target location.

Chunk Length: defines the maximum length of the recorded Video. The maximum Chunk Length is 12 hours, the default option is 2 hours (02:00:00:00).

• If the Recording does not reach the entered Chunk Length, the recorded clips will be automatically truncated to the expected recorded length.

• Recording exceeds the entered Chunk Length: A new Recording (generating a new clip) will automatically be started.

Start Timecode: Enabling this option overrides the local time or incoming timecode and makes every new clip start with the defined timecode value.

Port: port to access the Channel from just:in mac over an IP connection. The default port for the first Channel is 50000, 50001 for the second Channel, and so on. You can keep this setting if the chosen ports are not in use on this machine.

MXF Write Buffer (Bytes in binary): This setting can be used to tune MXF writing for specific storage requirements, but should only be changed with care as it may lead to unexpected results including write errors. Recommended value: “Block size of storage”.

VTR Control: Select the serial RS-422 connection you want to use to control your VTR.

VTR Preroll in Seconds: Set the desired VTR pre-roll value in seconds (1-10). The default value is “5”.

Restart On No Signal if Not Recording: If this option is enabled, the Channel will automatically restart after a signal loss (only in Idle Mode). Available options are:

• Close container, write to new: Recording to the current file will be stopped and as soon as there is a valid signal again the recording will start into a new file.

• Close container and stop: Recording will be stopped when a Channel detects a signal loss.

Cache Options:

• Don't Cache: files are directly written to disk, no caching is done.

• Cache (Default): tells the internal macOS Ethernet controller to cache data to flush it to the network stack later to improve write performance.

Action on Timecode break:

• Ignore: The Channel ignores timecode breaks.

• Create new file: The Channel creates a new file upon a timecode break.

Preview

You can manually override the resolution, frame rate, and quality of the Video Previews within Just Control. This may be helpful to increase performance when displaying many Channels in Just Control. Please refer to the Channel Preview Options below for more information.

Resolution: Two resolution options are available:

• High: 640×360px

• Low: 480×270px 

Frame rate: The preview frame rate can be changed between “0” (i.e. native frame rate) and “30” (if the channel frame rate is higher than “30”, then the preview will be limited to 30 fps).

Quality: The “Preview Quality” setting can be changed between “10%” and “100%” (the default value is “50%”).