Versions Compared

Old Version 1

changes.mady.by.user Thomas Staiger

Saved on

compared with

New Version Current

changes.mady.by.user Thomas Staiger

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Comment: optimized the described procedures

Before you begin make sure that you have OS X 10.10.5/10.11 or higher installed as well as the current drivers from Blackmagic Design (http://www.blackmagicdesign.com/support).  → Blackmagic Design.

Note

live:cut version 1.4.1 will ONLY run on OS X 10.10.5/10.11 or higher!

To install live:cut 1.4.1 drag and drop the LiveCut installer icon onto the Applications folder and click Agree to accept the license agreement. 

 

Image Modified

Image Added

Image Added

For NEW installations of live:cut

1.4.1:  Navigate to the

:

  1. → Download live:cut from our helpdesk. It is part of the just:in installer disk image.
  2. Open the just:in installer disk image.
  3. Drop the "LiveCut" icon onto the "Applications" folder below.
  4. Navigate to the folder /Applications/LiveCut
folder
  1. and double-click on Just In Engine QuickTime to initialize the software packages. You will be asked to update your system and to allow access to system resources such as Apple Calendar. Confirm all of them by clicking OK and by entering your credentials when asked.
 

Optional: Install the ToolsOnAir GPI Box driver

, so that you can

to connect to a vision mixer or switcher other than a Blackmagic Design ATEM. You can find

this

the driver on the just:in

the Just In installer ->

installer disk image in the folder Additional Content/Service USB Drivers

/ folder

. 

 

The next step is to configure

/

and activate your channel(s).

Proceed to page 4 to fine tune the configuration. 

Image Removed

Image Removed

Image Removed


For UPGRADE installations of live:cut

1.4.1 ONLY

:

 

In case of a previous activation of any version prior to v.1.4.1 you will need a new activation code. Please → contact ToolsOnAir to receive

your

an updated activation code under software maintenance

. To perform an upgrade install, you can follow the same steps above. Drag the LiveCut installer package to the Applications folder

.

  1. → Download live:cut from our helpdesk. It is part of the just:in installer disk image.
  2. Open the just:in installer disk image.
  3. Drop the "LiveCut" icon onto the "Applications" folder below and confirm that you want to replace
(Replace All) an older version of LiveCut
  1. the existing files.
 
  1. Navigate to the folder /Applications/LiveCut
folder
  1. and double-click on Just In Engine QuickTime to initialize the software packages. You will be asked to update your system and to allow access to system resources such as Apple Calendar. Confirm all of them by clicking OK and by entering your credentials when asked.

Optional: Install the ToolsOnAir GPI Box driver to connect to a vision mixer or switcher other than a Blackmagic Design ATEM. You can find the driver on the just:in installer disk image in the folder Additional Content/Service USB Drivers. 

Your capture presets

will be kept as well your

and channel(s) configuration will be kept. If you upgrade from a previous version of live:cut, you will need to recreate the destination presets in the Just In

Con guration

Configuration preference panel in order to reflect the new multiple destinations structure

(see page 7)

.

 

Once the upgrade setup is done, restart Just In Engine QuickTime, launch

the LiveCut GUI

live:cut, enter the activation code

(see section 4.4)

and connect to the desired channels.

 

If you're planning to connect to a vision mixer or switcher other than a Blackmagic Design ATEM, then you need to install the USB drivers for the ToolsOnAir GPI Box USB interface (available separately). You can find this driver in the Just In installer -> Additional Content folder. 

 

Where to look for live:cut v.1.4.1 components after the installation process

The live:cut installation process installs following components:

  • LiveCut: /Applications/LiveCut/LiveCut.app
  • Just In Engine QuickTime: /Applications/LiveCut/Just In Engine QuickTime.app
  • ToolsOnAir GPI Box drivers: Just In installer -> Additional Content/Service USB Drivers/

 

Info

In case of a previous activation of any live:cut version prior to v1.4.1, you will need to enter a new activation code. Please → contact ToolsOnAir to receive your updated activation code under software maintenance.