Table of Contents |
---|
Warningnote |
---|
Before proceeding you must stop the channel by deactivating the checkbox in front of it. Stopping the channel will also stop the Just Out engine and therefore the final outputYou must unlock the Just Control Configuration window and stop the channel(s) to be able to make any changes. |
It is possible to control 3rd party hardware devices like Video Routers, Switchers and GPI Devices, as well as insert SCTE104 triggers and send email notifications using the optional Events function. Before such a device can be controlled, it must be configured in Just Control first. After that, the crosspoints can be defined in the user interfaces.
...
.
Adding
...
a Device
Stop the desired Channel by deactivating the checkbox in front of it. Stopping a Channel will also stop the Just Out engine and therefore the final output.
Select the
...
Channelin the Devices & Channels list.
...
Click on the Events tab.
...
Device and protocol: Select the desired type of
...
device/event here. Some Routers may use the same protocol but are from different manufacturers. Make sure to select a protocol which is supported by your Router. If you are unsure about which protocol to use, ask the manufacturer or send a request to our support system. If a device supports only a certain setting please contact ToolsOnAir for assistance.
Timeout/Delay in seconds: For some devices a timeout can be defined here.
Serial port: Select and configure a serial connection. Check the user manual of your Router to find more information about the proper settings. If you are unsure about which settings to use, ask the manufacturer of the hardware device.
Ethernet: Configures an Ethernet connection. If your device supports network communication, configure the Ethernet connection here. This method is preferred and should be used whenever possible. If a device supports only a certain setting please contact ToolsOnAir for assistance.
Click on the Add… button to add the selected device to the list of Currently event devices of the Channel.
...
Save/Load Preset: Each device has its own ID which is used to identify the device in the playlist XML. To transfer the device ID to another system or to save it as a backup, the device can be saved and loaded here.
...
Info |
---|
|
Removing an Event Device
Select the desired Channel.
Go to the Events tab.
Select the Event Device in the Currently event devices list on the right.
Press the backspace key.
Accept the warning dialog to remove the Event Device. This cannot be undone.
Info |
---|
|
Adding Crosspoints in just:live or just:play
Start Just Control and there a just:live or just:play user interface.
Go to the Event tab in the the Library.
Click on the "+" button in the lower right corner of the Events tab.
Defining Crosspoints in just:live or just:play
Defining Event Presets for just:live, just:play and failover
Stop the desired Channel by deactivating the checkbox in front of it. Stopping a Channel will also stop the Just Out engine and therefore the final output.
Select the Channel in the Devices & Channels list.
Click on the Events tab and make sure, that at least one Device is defined under Type/Protocol.
Click on the Presets tab.
Click on Add Preset to open the Preset configuration window.
Name the Preset: The preset name given here will appear in the Event tab in the Library of just:live/just:play later. Change the name here once you saved a preset by clicking the
...
Add Preset button. Otherwise,
...
you will overwrite the previously saved preset.
Add
...
events: A
...
Preset can consist of one or more
...
Devices. For example, a preset can switch several outputs on a Video Router, or send one or more GPI Events, or even combine Video Router and GPI Events in a single preset. Select a Device and click Add. Repeat this for all Devices you would like to use with this Preset.
...
Configure Events:
...
Here you change the attributes which are provided by the Event.
Create Preset: When you have added all Events to the preset, click the Create Preset button to create the preset which will automatically appear in the Events tab in the Library of just:live/just:play. You can then use the preset(s).
...
Repeat steps 1 to 4 for each preset you need. When you are finished click the Done button.
...
Removing an Event Device or Preset
Stop the desired Channel by deactivating the checkbox in front of it. Stopping a Channel will also stop the Just Out engine and therefore the final output.
Select the Channel in the Devices & Channels list.
Click on the Events tab.
Click on the Devices or Presets tab.
Select the Device or Preset you would like to delete.
Press the backspace key.
Accept the warning dialog to remove the Event Device. This cannot be undone.
Info |
---|
|